ESP32 WT32-ETH01 Embedded Serial Port Ethernet WIFI Bluetooth Development Board

Description

Store Categories Store Categories Other Product View Details Features 1.ESP32-ETHO1 is an embedded serial to Ethernet module based on ESP32 series. 2. Module internal integration of optimized TCP / IP protocol stack, easy for users to easily complete the networking function of embedded devices, greatly reducing the cost of development time. 3.The module is compatible with half pad and connector through-hole design, the board width is universal width, you can directly weld the module on the board, you can also weld the connector, can also be used for breadboarding, convenient for users to use in different scenarios. 4.ESP32 series Ic is integrated 2.4GHz Wi-Fi and Bluetooth dual-mode Soc with good functional performance. 5.The module has super high RF performance, stability, versatility and reliability, as well as ultra-low power consumption. Specification Wi-Fi: Protocol: 802.11 b/g/n/e/i (802.11n, speed up to 150 Mbps; A-MPDU and A-MSDU aggregation, support 0.4 _s protection interval) Frequency range: 2.4~2.5 GHz Bluetooth: Protocol: Compliant with Bluetooth v4.2 BR/EDR and BLE standards RF: NZIF receiver with -97 dBm sensitivity Hardware: Network port specification: RJ45, 10/100Mbps, Cross Direct Adaptive Serial baud rate: 80~5000000 On-board Flash: 32Mbit Operating voltage: 5V or 3.3V power supply (either one) Operating current: 80mA on average Supply current: 500 mA minimum Operating temperature range: -40°C~+85°C Software: Wi-Fi Mode: Station/softAP/SoftAP+station/P2P Wi-Fi Security: WPA/WPA2/WPA2-Enterprise/WPS Encryption type: AES/RSA/ECC/SHA Firmware Upgrade: Remote OTA upgrade via network Software Development: SDK for secondary user development Network Protocol: IPv4, TCP/UDP IP acquisition method: static IP, DHCP (default) Simple pass-through mode: TCP Server/TCP Client/UDP Server/UDP Client User Configuration: AT+ command set Size: 63mm*25mm*16mm Supply Voltage: The power supply voltage of the module can be 5V or 3V3, and you can only choose one of the two. Power supply mode: Users can choose freely according to the demand: 1) Through-hole (soldered pins): Power supply by Dupont wire connection; Power supply by breadboard connection; 2) Half-pad (directly soldered to the board) : Power supply from the user's board. Instructions for use: Power-on instructions: If using DuPont cable: find the 3V3 or 5V power input port, connect the corresponding voltage, the indicator light (LED1) will light up, indicating successful power-up. Indicator light description: LED1: Power indicator, the light is on when the power up is normal; LED3: Serial port indicator, when RXD2 (IO5) has data flow, the lamp is on; LED4: serial port indicator, when TXD2(IO17) has data flow, the light is on; 4.3 Usage Mode Description Three ways of use, users can choose by themselves according to their needs: 1) Through-hole (Soldered Pin) : Connect with Dupont cable; 2) Through-hole (soldered pins): use on breadboard; 3) Half-pad: Users can directly solder the module on their own boards. Description of the working indicator of the network interface Green light: Connection status indication, when correctly connected to the network, the green light is on. Yellow light: data indication, blinking when the module has data received or sent, including the module received network broadcast packet List 1/2/5/10 x Module 2/4/10/20 x Pin(optional) Shipping Policy Payment Method Returns Policy Shipping Policy Payment Method Returns Policy Home Payment Shipping About us Contact us Copyright©2018 datacaciques Home Payment Shipping About us Contact us Store Categories Store Categories Other Product View Details Features 1.ESP32-ETHO1 is an embedded serial to Ethernet module based on ESP32 series. 2. Module internal integration of optimized TCP / IP protocol stack, easy for users to easily complete the networking function of embedded devices, greatly reducing the cost of development time. 3.The module is compatible with half pad and connector through-hole design, the board width is universal width, you can directly weld the module on the board, you can also weld the connector, can also be used for breadboarding, convenient for users to use in different scenarios. 4.ESP32 series Ic is integrated 2.4GHz Wi-Fi and Bluetooth dual-mode Soc with good functional performance. 5.The module has super high RF performance, stability, versatility and reliability, as well as ultra-low power consumption. Specification Wi-Fi: Protocol: 802.11 b/g/n/e/i (802.11n, speed up to 150 Mbps; A-MPDU and A-MSDU aggregation, support 0.4 _s protection interval) Frequency range: 2.4~2.5 GHz Bluetooth: Protocol: Compliant with Bluetooth v4.2 BR/EDR and BLE standards RF: NZIF receiver with -97 dBm sensitivity Hardware: Network port specification: RJ45, 10/100Mbps, Cross Direct Adaptive Serial baud rate: 80~5000000 On-board Flash: 32Mbit Operating voltage: 5V or 3.3V power supply (either one) Operating current: 80mA on average Supply current: 500 mA minimum Operating temperature range: -40°C~+85°C Software: Wi-Fi Mode: Station/softAP/SoftAP+station/P2P Wi-Fi Security: WPA/WPA2/WPA2-Enterprise/WPS Encryption type: AES/RSA/ECC/SHA Firmware Upgrade: Remote OTA upgrade via network Software Development: SDK for secondary user development Network Protocol: IPv4, TCP/UDP IP acquisition method: static IP, DHCP (default) Simple pass-through mode: TCP Server/TCP Client/UDP Server/UDP Client User Configuration: AT+ command set Size: 63mm*25mm*16mm Supply Voltage: The power supply voltage of the module can be 5V or 3V3, and you can only choose one of the two. Power supply mode: Users can choose freely according to the demand: 1) Through-hole (soldered pins): Power supply by Dupont wire connection; Power supply by breadboard connection; 2) Half-pad (directly soldered to the board) : Power supply from the user's board. Instructions for use: Power-on instructions: If using DuPont cable: find the 3V3 or 5V power input port, connect the corresponding voltage, the indicator light (LED1) will light up, indicating successful power-up. Indicator light description: LED1: Power indicator, the light is on when the power up is normal; LED3: Serial port indicator, when RXD2 (IO5) has data flow, the lamp is on; LED4: serial port indicator, when TXD2(IO17) has data flow, the light is on; 4.3 Usage Mode Description Three ways of use, users can choose by themselves according to their needs: 1) Through-hole (Soldered Pin) : Connect with Dupont cable; 2) Through-hole (soldered pins): use on breadboard; 3) Half-pad: Users can directly solder the module on their own boards. Description of the working indicator of the network interface Green light: Connection status indication, when correctly connected to the network, the green light is on. Yellow light: data indication, blinking when the module has data received or sent, including the module received network broadcast packet List 1/2/5/10 x Module 2/4/10/20 x Pin(optional) Shipping Policy Payment Method Returns Policy Shipping Policy We will arrange shipping for you within 24 Hours after payment cleared except the holidays. -We ship items to Worldwide. Thank you! -we will ship out the order in 1-2 business days after payment cleared .Since it is international shipping ,delivery time is about 15--28 business days to arrive to most countries. Payment Method We accept PayPal payment ONLY, and must be received within 5 days from the date of purchase. 2. It is easy and safe for you to pay by credit cards, debit cards, bank transfers and PayPal account balances. 3.Buyers are responsible for import duties,custom fees and taxes, if any, please check your country. Returns Policy 1.We believe our items are so outstanding. We are convinced you will be happy with your Purchase. 2. If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund or resend the item to you after the returned item arrived at our warehouse. 3. Please include your eBay ID and item number with any email requests.